- 您现在的位置：买卖IC网 > Sheet目录1316 > 3-1470213-6 (TE Connectivity)CONN HEADER 36POS DL 2MM T/H 8AU
108-57197
3.3. RATINGS
A. Voltage: 250 VAC rms.
B. Current: 1 A Max
C. Operating Temperature: -40°C to + 105°C
3.4. PERFOMANCE AND TEST DESCRIPTION
The product is designed to meet the electrical, mechanical and environmental
performance requirements specified in Table 2. All tests are performed at
ambient environmental conditions per AMP Specification 109-1 unless otherwise
specified.
3.5. TEST REQUIREMENTS AND PROCEDURES SUMMARY
NO.
3.5.1
TEST ITEMS
Examination of
Product
REQUIREMENTS
Meets requirements of product
drawing. No physical damage.
PROCEDURES
Visual inspection.
ELECTRICAL REQUIREMENTS
3.5.2.1
Termination
Resistance
Initial
Final
20m ohms max.
30m ohms max.
Subject mated contacts assembled in
housing to closed circuit current of 50mA
max at open circuit voltage of 50mV max.
(See Fig. 1)
3.5.2.2
Insulation
Resistance
1000M ohms min. (Initial)
1000M ohms min (Final)
Measure by applying test potential between
adjacent contacts, and between the
contacts and ground in the mated connector
assembly.
MIL-STD-202, Method 302, Condition B
3.5.2.3
Dielectric Strength
Connector must withstand test
potential of 650VAC for 1 min.
Current leakage limit to 5.0mA
max.
Measure by applying test potential between
adjacent contacts, and between the
contacts and ground in the mated connector
assembly.
MIL-STD-202, Method 301
MECHANICAL REQUIREMENTS
3.5.3.1
Individual Pin
Insertion/ Extraction
Force
Insertion Force
200 gf max
Extraction
Force
10gf min
Subject terminated contact and pin to mate
and unmate to measure the force required
to insert and extract by operating at a rate of
100mm a minute. (See Fig. 2)
3.5.3.2
3.5.3.3
3.5.3.4
Receptacle Contact
Retention Force
Post Retention
Force
Solder ability
250 gf min. per contact
0.5 kgf min. per contact
The inspected area of each lead
must have 95% solder coverage
minimum.
Apply axial load to terminated contact at a
rate of 25mm a minute.
Apply axial pull-off load to post contact
mounted on housing and measure the force
required to dislodge post from housing.
Steam Aging Preconditioning ：
(1) Tin 、 Tin-Cu Coating:
93+3/-5 ℃、 100% HR 、 8hrs.
<J-STD-002 category 3 aging>
(2) Other Coating:
93+3/-5 ℃、 100% HR 、 1hrs.
<J-STD-002 category 2 aging>
Solder pot temperature: 245 ± 5 ℃ , 5sec
Rev
B
2 of 5
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
3-1478985-0
CONN PLUG SMA DUST CAP W/CHAIN
3-1478986-0
CONN SMA JACK CAP W/CHAIN
3-1489841-3
CONN MEMORY SCKT 240P 400TL 15AU
3-1532006-0
CONN PLUG SOS/LEPRA STR 50 OHM
3-1546099-0
CONN BARRIER BLOCK 30CIRC 6.35MM
3-1546119-9
TERM BLOCK 22CIRC VERT .250
3-1546159-9
CONN BARRIER BLOCK 24CIRC 9.53MM
3-1546307-0
CONN BARRIER BLOCK 30CIRC 9.53MM
相关代理商/技术参数
3-1470213-8
制造商:TE Connectivity 功能描述:CONN UNSHRD HDR HDR 38 POS 2MM SLDR ST TH - Bulk
3-1470226-0
制造商:TE Connectivity 功能描述:CONN SCKT STRP RCP 30 POS 2MM SLDR ST SMD - Tape and Reel
3-1470226-2
制造商:TE Connectivity 功能描述:CONN SCKT STRP RCP 32 POS 2MM SLDR ST SMD - Tape and Reel
3-1470226-6
制造商:TE Connectivity 功能描述:CONN SCKT STRP RCP 36 POS 2MM SLDR ST SMD - Tape and Reel
3-1470226-8
制造商:TE Connectivity 功能描述:CONN SCKT STRP RCP 38 POS 2MM SLDR ST SMD - Tape and Reel
3-1470250-3
制造商:TE CONNECTIVITY 功能描述:
3-1470252-0
制造商:TE Connectivity 功能描述:1.0MM FPC SMT R/A TOP 30P - Tape and Reel
3-1470260-0
制造商:TE Connectivity 功能描述:CONN SCKT STRP RCP 30 POS 2MM SLDR RA TH - Rail/Tube